Electronics

,

Dev Journal: Simulator for Fluorescence the VFD Clock & Firmware Version 3.0

,
Dev Journal: Simulator for Fluorescence the VFD Clock & Firmware Version 3.0

Fluorescence by The VFD Collective Developer Journal: Home office, writing a simulator for Fluorescence & introducing how its new firmware 3.0 is structured and works under the hood.

,

Fluorescence & More: Dear Fellow Creators

,
Fluorescence & More: Dear Fellow Creators

Just a warm hello from me. It's been a long time since I have made some public blog posts or announcements. So here I am now, with a few really exciting things to announce. Let's get right into it

Create with The VFD Collective: DIY Kit Large Pictures

When assembling the FLUORESCENCE DIY kit, we hope you find large reference picture helpful. So for every major step, here are reference pictures of how the clock should look like when finished.

_asmm_0_reference.jpg

It's the little things in life: We begin by soldering everything that is not-so-tall (low profile) and has only two pads. Download the full size picture HERE.

_asmm_6_2_reference.jpg

We're done when all the LEDs on the top layer are in place. Download full size picture HERE.

_asmm_B_1_reference.jpg

A startup circuit for minimalists: Let's make it shine, even when the tubes are not placed yet. With the firmware microchip attached, we are already able to use the LEDs and the clock. Can you tell what time it is by looking at the colors in resistor mode? Download full size picture HERE.

_asmm_B_0_reference.jpg

You're my flashlight: On top, all the lights are controllable by messing around with the buttons or setting with USB. Download full size picture HERE.

Done! This is the back side with all components. Please note the direction of IC1 to IC6 (upside down!)

Known Issues

  • 04/08/18: #003 Tube segment not correctly off. Likely, the corresponding HV driver IC (IC13 ... IC17) is damaged. If your DIY kit is affected by this issue, please use the contact formula and provide your DIY kit serial number to receive equivalent replacement parts sent to you for free. Please also tell the amount of HV driver ICs to be replaced

  • 04/08/18: #002 USB IC (CH340G) not working. If your DIY kit is affected by this issue, add two capacitors (22pF, 0805 size) to the position of C12, C13 respectively. Please use the contact formula and provide your DIY kit serial number, the 2x 22pF 0805 capacitors will be sent to you for free!

  • 04/08/18: #001 General Soldering Reference missing. For some DIY kit orders, the General Soldering Reference is missing. If your DIY kit is affected by this issue, find the digital (PDF) version in the resources section below. Please use the contact formula and provide your DIY kit serial number if you wish to have a physical copy of the General Soldering Reference for free as well!

  • This will be the list of issues for the assembly manual of FLUORESCENCE DIY

  • Please report issues to info@thevfdcollective.com or click here. Thank you for your help.

,

Preparing Fluorescence Kits & The VFD Collective is now on GitHub!

,
Preparing Fluorescence Kits & The VFD Collective is now on GitHub!

Berlin. It's one of those days in January where most of the people just get up and go to work because they really have to. Not that it's freezing outside. No not even close. Just the grey, dreary sky and the light drizzle going on, probably for weeks again, already...

,

Designing Your Own VFD Clock II: The Functional Circuit

,
Designing Your Own VFD Clock II: The Functional Circuit

While our last focus was on the IV-11 VFD tube - since we had to design a circuit that make the tubes glow and display the stuff we want it to, now the microcontroller is in the spotlight for adding fundamental features, such as a real time clock to the circuit.

The second part of the article...

,

Designing Your Own VFD Clock I: The Tube Circuit

,
Designing Your Own VFD Clock I: The Tube Circuit

This blog entry shows you what makes my VFD tube clock work and I will take you through the process of turning some tubes, parts and lines of code into a glowing tube clock. It's great and easy to follow this Instructable if you have some basic electronics knowledge already, but down't worry if not. I'll do my very best to keep everything short and simple. 

The first part is about the tube and...